Below is a list of the different prefixes and their meanings. Many values to settings may be changed via the in-game settings menu and the console.
The in-game settings menu may be accessed by pressing the Escape Esc key and clicking Settings. The Audio submenu changes the volume of different kinds of sounds. Some mods like Audio Overhaul for Skyrim change the default kinds of sounds listed here.
The setini command changes values to settings while in-game. Some settings will immediately change in-game, but others will not. Current values for settings may be retrieved by using the getini command.
Floating point values are not displayed beyond two decimal places. It is also possible to refresh the values of some settings from the INI files if changed after launching Skyrim by typing the refreshini command in the console. The saveini console command is not recommended to be used except for research purposes, as some of the values to the settings which that command prints out are only accurate to four decimal places and unequal to the proper default values.
It should be noted, however, that the saveini command prints out all settings recognized by the game to the default SkyrimPref. Both must be removed after use for the game to function properly. This guide assumes that the user has either followed the current STEP Guide or has jumped over to this guide whilst following the main guide. The following instructions expect the unedited default INIs created in section 1.
After deleting them, the default versions can be regenerated by running the Skyrim Launcher again as described in section 1. Users with MO already installed and set up will have to run the Launcher via MO to reset the defaults for the profile.
Copy the following tweaks into the correct INI file inside their respective [sections]. If the setting already exists, change the value to the one below. If the setting does not exist, enter it on a new line at the end of its [section].
If the [section] does not exist, create it on a new line below one of the [sections]. Carefully check to ensure that there are no:. Increase third-person zoom speed fMouseWheelZoomSpeed sets the transition speed when zooming in and out in third person mode. This also affects how fast the transition from first to third person occurs. More accurate aiming with bows and crossbows f1PArrowTiltUpAngle sets the upward tilt angle of arrows in first-person view.
It is recommended to change this so that arrows more accurately hit where the crosshair is pointing, although some arching is "natural. Unfortunately, there is no similar setting for third-person view. It is recommended to change this so that bolts more accurately hit where the crosshair is pointing. Once over three megabytes in size, the files seem to become corrupt. ENBoost 's screenshot functionality effectively replaces it. Smooth sun-shadow transitions fSunShadowUpdateTime sets the speed of sun-shadow transitions in seconds.
It is recommended to be adjusted to minimize the transitions. The value here increases the speed of the transition from one second to a quarter second. A value of 0. Increasing this also increases the distance the shadows will move during the transition. The tweak here increases the time between transitions from 10 to 30 seconds, causing the transition to move the shadows three times as far.
Enable or disable vertical sync iPresentInterval toggles vertical sync between frame render and screen refresh rate, removing screen tearing. Despite being erroneously placed in the SkyrimPrefs. It is recommended to be left at 1 enabled , which is its default value. Setting it to 0 will disable it, which may be useful if another form of vertical sync or a frame rate limiter is used.
Disable the intro video sIntroSequence sets the intro video before the main menu. It is recommended to set it to blank for faster startup. Prevent lighting pop-in Raising fFlickeringLightDistance is believed to prevent lighting pop-in.
It is recommended to adjust fGrassFadeRange rather than increase fGrassStartFadeDistance to remove the grass pop-in effect and performance benefits over the latter. Increasing this will create more diverse kinds of grass, especially with grass mods such as SkyrimLE:Skyrim Flora Overhaul at a small performance cost. Without grass mods, changing this setting produces little effect. Negative values disable grass. It is recommended to increase this from its default value, 2, to 3.
Adjust grass density iMinGrassSize sets the grass density. Lower values produces greater density, but values between 1 and 40 look almost identical. A value of 0 removes all grass.
Negative values e. High values starting around 50 and higher noticeably decrease grass density at a small performance gain. Grass mods such as Grass on Steroids and Verdant take advantage of this and can create high density grass at high iMinGrassSize values. Setting iMinGrassSize too high e. STEP recommends to increase this to Disable the in-game tutorial pop-ups bShowTutorials toggles the in-game tutorial pop-ups. It is recommended to disable them set to 0 once accustomed to the game.
Increase map menu rotation range fMapWorldYawRange sets the yaw range that the map menu's camera can turn when the right mouse button is pressed.
Setting this to allows the user to rotate full circle once. Text Imports System. RegularExpressions Imports System. Please post a clean copy of the prefs. Note: This is ONLY to be used to report spam, advertising, and problematic harassment, fighting, or rude posts. Open Skyrim. Aug 28th, Double D. Posted November 16, Start your game and play for a minute and then look again. When you search for files video, music, software, documents etc , you will always find high-quality skyrim ini download files recently uploaded on DownloadJoy or other most popular shared hosts.
Sign in Sign up Instantly share code, notes, and snippets. Currently Skyrim on switch can only have a max of 10 ESP enabled mods. Basierend auf den Ultra Settings des Enderal Launchers. These files are plain text files with a basic structure comprised of properties and sections.
Sign Up, it unlocks many cool features! Create a new folder named SKSE and open it. I have the skyrimPrefs and skyrimCustom, Do I need both?
They're present in most games and have nothing to do with console settings. Salut je ne trouve pas Skyrim. Not a member of Pastebin yet? Skyrim INI File. I downloaded the ultimate skyrim ini files but I can't find the ultimate skyrim profiles folder in the image. Bash only reads the Skyrim. Die Konfigurationsdateien findet ihr unter.. Need to turn off shadows. Originally posted by Mr. Monday :. I don't see it there either, although I do see a config file just labeled Skyrim.
Are they the same thing? Originally posted by Falro the Great :. Eldyy View Profile View Posts. Originally posted by Shamefur Dispray :. Per page: 15 30 Foxwolfmoon View Profile View Posts. Thanks, Incunabulum. For those also having this issue, here's the instructions for turning off the "hide system files" option. Dabbertron View Profile View Posts. All I have is skyrimprefs and skyrim.
Playing at fps now. Need to turn off shadows. Can't turn them off. Tried everything.
0コメント